Poultry Watering Accessories

Our accessories are the perfect way to your complete VAL-CO Watering System AND we can even help you to upgrade your existing non-VAL-CO watering system! We offer various adapters that enable you to use our best drinkers on watering lines that may not be VAL-CO's.

Water Filter

VAL-CO’s water filter has a patented backflush system that makes it ideal for “whole-house” water filtration in homes, farms, private wells, restaurants, greenhouses, pools, spas or trickle irrigation. It can handle up to a 40 G/M flow rate with minimal pressure drop. With just the turn of a few knobs, you can reduce suspended sand, silt, scale, rust, unseen particles, foul odors, even the taste of chlorine (with optional filter cartridges)... for clean, clear water.

Water Chiller

Normal high pressure well systems which provide cool water do not need this cooling unit. Cooling unit should only be used when incoming water temperature is approx. 70°F or above. Water chiller has an adjustable program which only runs when you, the grower, think the incoming water is too hot. Incoming water temperature can be cooled up to about 25°F.

Start-Grow Bracket

The standard Start-Grow bracket (BG220) is located in the cage partition and holds two Val drinkers on each side of the cage partition. The bracket moves freely up and down for ease in height adjustment. Also available is our extended Start-Grow bracket (BG219), which is designed to raise the Val drinkers to the top of the cage in the cages that have the cage leg stands going through the cage. This helps to keep the pits dry, and makes it easier for the birds to drink.

Breeder Shield

Keeping floors drier has never been easier with VAL-CO's Breeder Shield. When attached to your breeder watering line, the Breeder Shield eliminates side triggering, helping prevent water from hitting the floor. It also locks the nipple in place so it can't accidentally twist out.

Euro Cup

The Euro Cup keeps the floor dry even when using the extra high flow drinkers. It is designed to be used with any of the VAL-CO saddles.

Competition Adapters

Retrofit your existing non-VAL-CO watering systems with our complete line of adapters and drinkers.

Replacement Drinker for Ziggity Short Cap (VR150ZS)

This is a direct replacement for the Ziggity J-Lock style drinker. This drinker has all of the same quality precision internal parts as our standard Val Drinkers; but with a slightly longer cap & modified flow pin. These modifications allow this drinker to fit into the Ziggity saddle, without the need to replace the pipe, suspension or winching hardware. Available as a Roaster, Broiler or Layer Drinker.

Replacement Drinker for Ziggity Long Cap (VR150ZL)

Same as the replacement drinker for the Ziggity short cap, except this drinker has a much longer cap to replace the Ziggity J-Lock with the long cap. Again, with this drinker, you get the Val quality you’ve come to expect without replacing the pipe, suspension or winching hardware. This drinker is available as a Roaster, Broiler or Layer Drinker.

Replacement Drinker for Clark System (VR150C)

This is a standard Val Drinker with a slightly modified flow pin to fit in the Clark saddle. The Clark saddle does not have the necessary clearance for the “feet” on the bottom of the Val flow pin, thus this drinker has a straight flow pin with no feet. Using this drinker to replace the Clark J-Lock, there is no need to replace the pipe, suspension or winching hardware. Available as a Roaster, Broiler or Layer Drinker.

Saddles for Threaded Drinkers (VS205L / VS405L)

These saddles are a replacement for .875&rdquo square pipe (VS205L) or 1.1&rdquo square pipe (VS405L) that previously had threaded drinkers. The stems are slightly larger than the standard glued saddles so they can be glued into the existing threaded hole. These saddles accept any of our standard J-Lock Drinkers.

Threaded Nipple Replacement (VR150THD)

This drinker is a replacement for Lubing or any of the European style threaded drinkers. The internal parts have the same quality precision internal parts as our standard Val Drinkers. The major benefit of this drinker is that once it has been threaded into the pipe, the internal components can be removed without removing the unit from the pipe – preventing damage to the threads in the pipe. Available as a Roaster, Broiler or Layer Drinker.

Replacement Plasson Saddle Kits (VP500)

This kit includes a replacement saddle (with a new seal) that will accept any of our standard J-Lock drinkers. This is a direct replacement for the Plasson drinker – there is no need to replace the pipe, suspension or winching hardware.

Replacement Adapter Kit for Ziggity Standard ACE [not for big ACE] (VZA150)

This kit includes a replacement adapter (with a new O-ring) to replace the Ziggity Twin lock style drinker. This adapter will accept any of our standard J-Lock drinkers. This retrofit saddle locks into the Ziggity twin lock saddle, then our J-Lock can be installed into it – without replacing the pipe, suspension or winching hardware.

Replacement Chore-Time Adapter Kit (VCTB110-K)

This kit, which includes a replacement adapter and new O-ring seal, replaces Chore-Time drinkers and will accept any of our standard J-Lock drinkers. With this adapter there is no need to replace your pipe, suspension or winching hardware to upgrade to VAL-CO watering.

Replacement Chore-Time & Lubing Hanger Clips (VA505)

This replacement hanger clip is for use with Val Pipe on Chore-Time or Lubing aluminum suspension. The drinker pipe must be replaced with new Val Pipe, but the existing suspension and winching can be used.

Hanger Bracket for 3/4” Conduit (VH341)

This hanger bracket can be used when the customer wants to replace the drinker pipe, and use their existing 3/4&rdquo (1.050&rdquo od) conduit. With this hanger, the existing conduit, suspension and winching hardware can be used.